DODGE RAM FORUM - Ram Forums & Owners Club! - Ram Truck Forum - View Profile: HemiLonestar
DODGE RAM FORUM - Ram Forums & Owners Club! - Ram Truck Forum

Go Back   DODGE RAM FORUM - Ram Forums & Owners Club! - Ram Truck Forum > Members List


Notices


Vendor Highlight! - Check these guys out for great deals on Parts and Accessories!
HemiLonestar is a jewel in the roughHemiLonestar is a jewel in the roughHemiLonestar is a jewel in the roughHemiLonestar is a jewel in the rough

HemiLonestar HemiLonestar is offline

Dodge Ram Forum Senior Member

Visitor Messages

Showing Visitor Messages 1 to 10 of 16
  1. RogerRamJet
    02-10-2016 01:08 PM
    RogerRamJet
    Gooooood, goooooood. HA!
  2. RogerRamJet
    01-06-2016 01:13 AM
    RogerRamJet
    Thanks for the laugh, Sam!

    The admins may make you change your avatar, but it sure is funny.
  3. dustinlee
    01-19-2015 09:54 PM
    dustinlee
    About 9 days if I remember right.
  4. dustinlee
    01-13-2015 08:41 PM
    dustinlee
    Yea about 6 months ago or so. It was ok, my experience was more complicated than it should have been, I had a rusted out screw on my main harness plug that mounts to firewall behind the battery box. But it was worth it, and Chris Squire from hot wire was very helpful.
  5. Crabby
    01-09-2015 06:36 PM
    Crabby
    thanks i'll try that. Dodge replaced part of the exhaust because it made a cherping sound like the muffler guts were loose at the same time it tries up shifting to all cylinders????
  6. Crabby
    01-08-2015 09:42 PM
    Crabby
    Hey,
    Is anyone having vibration problem in their 6.4 hemi when it shifts out of the economy mode and all cylinders kick in ?
    Crabby
  7. KelseytheDodgeGirl
    06-07-2014 03:29 PM
    KelseytheDodgeGirl
    Hey man,
    I was searching through the 3rd Gen forums, trying to figure out how to get my front bumper fascia off. I found an old post here saying that you had taken out those little 'screw' looking things, but they ended up being destroyed.

    I wasn't sure if you would get the post if I asked on that thread.
    Here's my question-- Where did you get replacements for them, or where would they be sold? I found some online, but they're going for $10 a pop because they're Chrysler OEM.

    I don't care who made them as long as they hold the bumper cover/fascia in place...

    Any help or insight is really appreciated!
    Thanks!
    -Kelsey
  8. LuvBug915
    06-13-2013 03:10 PM
    LuvBug915
    having trouble locating the crankshaft position sensor. can you send me a link with better instructions? i have looked online and many videos and other instructions are not very clear.
  9. Twitch02x
    07-19-2012 10:26 AM
    Twitch02x
    Ok so I can't get away with just putting motor in and running it as is
  10. Twitch02x
    07-18-2012 08:39 PM
    Twitch02x
    Hey bud do you know much about mds I was told I need to remove mds lifters and replace with non mds lifters if I'm gonna put the motor Into a non mds vehicle my number is 2818832807 if you have time gimme a call

About Me

  • About HemiLonestar
    Location
    MD
    Interests
    Cars and boats
    Occupation
    CG Engineer
    Gender
    Male
  • VEHICLE INFO
    Enter your vehicle info here!
    Vehicle
    2003 Dodge Ram 1500 QC
    Trim Level
    SLT Lonestar Edition
    Color
    Flame Red
    Engine
    2003-2008 345ci (5.7L) Hemi V8 345hp 375lb/ft
  • MODS LIST!
    Enter all the mods you have done to your truck here!
    MODS LIST!
    Ram:
    Mopar Borla catback; Taylor shorties
    SRT-10 front suspension/brakes & Bilstein shocks
    SRT-10 Dana 60 4.56 with SRT brakes
    Extang Revolution tonneau
    SRT-10 interior pieces
    AirRaid CAI; Superchips tune; TMR delete
    06-08 tailgate spoiler; Sonnax; Power wire
    Air Ram scoop; Circle D 2800 stall converter
    Bumper grille; Daytona lip; Daytona running boards
    Tow mirrors; 45 oil filter adapter; SRT-10 hood
    Rear inner fender liners; Belltech rear sway bar

    Near future:
    06+ coil conversion; Comp 260 (maybe)
    2005 PCM conversion; Eagle heads
    Eagle truck intake; 4th gen Vararam
    4th gen seats & console (possibly with functioning shifter)
  • Signature

    "Big Red"
    2003 Ram 1500 QC Hemi Lonestar "Big Red"
    2006 Charger R/T "Little Red", 2005 Magnum R/T
    (Mods list in profile)

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: 10-20-2017 12:45 AM
  • Join Date: 11-29-2009
  • Referrals: 0

Friends

Showing Friends 1 to 10 of 12

Contact Info

Instant Messaging
Send an Instant Message to HemiLonestar Using...
This Page
http://www.ramforumz.com/member.php?u=5871

MODS LIST!

MODS LIST!
Ram:
Mopar Borla catback; Taylor shorties
SRT-10 front suspension/brakes & Bilstein shocks
SRT-10 Dana 60 4.56 with SRT brakes
Extang Revolution tonneau
SRT-10 interior pieces
AirRaid CAI; Superchips tune; TMR delete
06-08 tailgate spoiler; Sonnax; Power wire
Air Ram scoop; Circle D 2800 stall converter
Bumper grille; Daytona lip; Daytona running boards
Tow mirrors; 45 oil filter adapter; SRT-10 hood
Rear inner fender liners; Belltech rear sway bar

Near future:
06+ coil conversion; Comp 260 (maybe)
2005 PCM conversion; Eagle heads
Eagle truck intake; 4th gen Vararam
4th gen seats & console (possibly with functioning shifter)

Advertisement



All times are GMT -4. The time now is 01:35 AM.


Copyright © VerticalScope Inc. All rights reserved.
Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
vB.Sponsors