DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum

DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum (http://www.ramforumz.com/index.php)
-   2011 Dodge Ram Forum (http://www.ramforumz.com/forumdisplay.php?f=117)
-   -   New Flaps (http://www.ramforumz.com/showthread.php?t=111311)

blrmkr 04-26-2012 07:00 PM

New Flaps
 
I did my first add on today. I put some Husky mud flaps on the front and back. They were super easy to install and don't look too bad. I was kind of worried about how they would look on the truck, but they're not that noticable.

http://i862.photobucket.com/albums/a...-39-42_537.jpghttp://i862.photobucket.com/albums/a...-39-20_826.jpg

y2kflhr 04-26-2012 07:56 PM

looks good, I need to get a set soon, the dirt goes pretty far up the truck when you run through puddles.......

Hex 04-26-2012 08:01 PM

Very nice, looks good. Where'd you get them? what was the install like? just self taping screws or what?

ArmyRXP 04-26-2012 08:27 PM

Looking Good!!!!! Very nice looking truck you got there.

dgard61 04-26-2012 08:47 PM

[QUOTE=blrmkr;786067]I did my first add on today. I put some Husky mud flaps on the front and back. They were super easy to install and don't look too bad. I was kind of worried about how they would look on the truck, but they're not that noticable.

Looks good! Have the same one's on my 2010. Only one's I could find to fit with the fender flares. Hope you used the clear 3M Protective film that came with them. The mud flaps will rub the paint off in no time. Great lookin' truck!

blrmkr 04-26-2012 10:57 PM

Thanks all. They are Husky Liners mud flaps and I got them from Summit Racing. $29.65 a pair, free and fast shipping. The front are held on with 2 factory screws that are for the fender flares. The backs use 2 factory screws and you have to drill 1 hole. I had to take the wheel off to fit the drill in there. The fronts fit perfect, but the back is off a little. The rear fender flare isn't square like the front, but the flap looks like it was made for a square one. The bottom fits good though.

Front:
http://i862.photobucket.com/albums/a...9-40-36_15.jpg

Rear:
http://i862.photobucket.com/albums/a...-40-19_708.jpg

edd5 04-26-2012 11:51 PM

I just put Duraflap mudflaps on my truck last week, pix in the 2012 forum. No drilling required, use factory screws. Didn't even have to remove lower corner trim spats. Fit nice. They make em for trucks with and without flares. More expensive though.
http://www.ramforumz.com/attachment....4&d=1334953982

Hex 04-27-2012 03:58 PM

Looks real good man. The funny thing about the back being off is that no one will ever notice unless you point it out, but it'll bug the hell out of you. I have stuff like that on ym truck, I try not to stare at it whenever I walk past. I think you did a good job


All times are GMT -4. The time now is 04:59 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vB.Sponsors
= Copyright RamForumZ.com a Gigathreads.com Network Site =Ad Management by RedTyger