DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum

DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum (http://www.ramforumz.com/index.php)
-   Custom Dodge Ram Performance Mods - Engine - 4.7 Liter V8 (http://www.ramforumz.com/forumdisplay.php?f=13)
-   -   Thinking of Spraying your 4.7? This is what you have to do (http://www.ramforumz.com/showthread.php?t=138079)

Darkknight3829 04-01-2013 05:42 PM

Thinking of Spraying your 4.7? This is what you have to do
 
Alright first off I am now currently spraying a 100 shot in my 2010 Dodge Ram 4.7L RCSB. This advise is based off a 100 shot and only a 100 Shot.

First I purchased all 16 Plugs. And installed. For this you will need a thin wall socket for your sparkplugs. I grabbed one from O'Reileys. I posted a picture with the correct measurement it should be.
Denso 3381 K20HR-U11 Nickel Spark Plug
http://i134.photobucket.com/albums/q...9/IMG_2160.jpg
Exhaust Plugs
http://i134.photobucket.com/albums/q...9/IMG_2164.jpg
Intake Plugs
http://i134.photobucket.com/albums/q...9/IMG_2165.jpg
http://i134.photobucket.com/albums/q...9/IMG_2166.jpg
http://i134.photobucket.com/albums/q...9/IMG_2167.jpg
http://i134.photobucket.com/albums/q...9/IMG_2176.jpg


Next I changed the Tstat to a 180 Performance Tstat
http://i134.photobucket.com/albums/q...9/IMG_2177.jpg
http://i134.photobucket.com/albums/q...829/image5.jpg

Next you need to get a custom tune for specifically a 100 shot of nitrous. I had my tune made by Sean Powell @ HEMIFEVER TUNING
http://i134.photobucket.com/albums/q...829/image2.jpg

I then installed the nitrous kit along with a purge kit and fuel pressure safety switch. Bottle heater is left to install.

http://i134.photobucket.com/albums/q...829/image3.jpg
http://i134.photobucket.com/albums/q.../IMG_22821.jpg
http://i134.photobucket.com/albums/q.../IMG_22841.jpg
http://i134.photobucket.com/albums/q.../IMG_22851.jpg
http://i134.photobucket.com/albums/q.../IMG_22861.jpg
http://i134.photobucket.com/albums/q.../IMG_22881.jpg
http://i134.photobucket.com/albums/q...ps7261b14e.jpg

Darkknight3829 04-01-2013 05:44 PM

http://i134.photobucket.com/albums/q...psc2a5864b.jpg
http://i134.photobucket.com/albums/q...ps9f939e1e.jpg

http://www.youtube.com/watch?v=HyVXFtFgT8w

A race against a 12 5.0 regular cab F-150. His mods, CAI, exhaust and tune. 14 second truck.
My mods, CAI, exhaust, nitrous tune, 3000 stall on a 100 shot
2010 dodge ram 4.7


http://www.youtube.com/watch?v=FmxRYmslleM

snrusnak 04-01-2013 06:07 PM

Congrats bud! I'm glad it didn't blow up :)

Thanks for posting all the info, it takes a long time to figure this stuff out, so it's good others will have something to look at for reference.

Darkknight3829 04-01-2013 06:24 PM

haha yea i am too!!
For sure, i hope it will help.. It took us forever to figure this out.

moparornocar72 04-02-2013 11:23 PM

What did you mount your purge too? I see it going toward the windshield wiper but couldn't tell.

Darkknight3829 04-03-2013 12:08 AM

Towards the top where your hood closes there is a plastic piece that runs along the length of your windshield. Under the rubber seal there is a plastic piece with sheet metal re-enforcing it on the bottom. I used self tapping screws to secure the brackets to the plastic and sheet metal part. It has been a very sturdy place to put them so far.


All times are GMT -4. The time now is 09:34 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
vB.Sponsors
= Copyright RamForumZ.com a Gigathreads.com Network Site =Ad Management by RedTyger