DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum

DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum (http://www.ramforumz.com/index.php)
-   Dodge Ram Wheels And Tires (http://www.ramforumz.com/forumdisplay.php?f=129)
-   -   20x10 Fuel Hostage wheels what's the correct offset? Need input ASAP... (http://www.ramforumz.com/showthread.php?t=143132)

1LOWBLKRAM 05-24-2013 12:45 PM

20x10 Fuel Hostage wheels what's the correct offset? Need input ASAP...
 
Hey guys/gals I'm looking at picking up a set of Fuel Hostage Wheels and want to go with the 20x10 setup to get the deeper lip. Is a -12 offset correct? How far will the wheels stick out? Going with Nitto Trail Grappler 35x12.50x20.

Thanks

No fender flares on yet but they are in my plans.

gonefishin776 05-24-2013 12:48 PM

that'll work. with those 10" wide wheels and the -12mm offset you'll probably stick out a good bit. Esp because those tires run wider than 12.5"...more like over 13". I'd say atleast 2.5 inches you'd stick out. Probably more. It'll look good tho! esp with some flares

1LOWBLKRAM 05-24-2013 01:48 PM

I'm running the Rough Country leveling kit 2.50 upfront and 1.75 in the rear.
What offset would work best to keep the wheels a little more flush?

gonefishin776 05-24-2013 02:18 PM

not exactly sure. probably closer to a 0 offset

brandonjansen 05-24-2013 04:37 PM

With a 20x10 wheel -12 offset is the lowest you can go. Any lower and you'll end up rubbing on the UCA.

You posted on my other thread about my wheels and tires so I'm assuming you saw how far I'm sticking out front and back. I'm a 2 1/8" on the front, you'll be approximately 0.5" further than that so you're looking at 2 5/8". On the back you'll be at around 2 1/8". So that is a significant amount of poke especially if you only plan on keep the truck leveled and not lifting it in the future. I can tell you right now you're also going to have problems with rubbing. Specifically on the back of the inner fender. I JUST clear mine with turning (and that was with some modification to the inner fender) so you will rub for sure. You will definitely be trimming the plastic and possibly bending the metal behind it a little bit as well.

If you want to stay as flush as possible you need a 20x9 0 offset. With that you'll be sticking out around 1 5/8" on the front and 1 1/8" on the back. So still poking a bit to get a nice stance.

1LOWBLKRAM 05-24-2013 05:08 PM

Quote:

Originally Posted by brandonjansen (Post 1106887)
With a 20x10 wheel -12 offset is the lowest you can go. Any lower and you'll end up rubbing on the UCA.

You posted on my other thread about my wheels and tires so I'm assuming you saw how far I'm sticking out front and back. I'm a 2 1/8" on the front, you'll be approximately 0.5" further than that so you're looking at 2 5/8". On the back you'll be at around 2 1/8". So that is a significant amount of poke especially if you only plan on keep the truck leveled and not lifting it in the future. I can tell you right now you're also going to have problems with rubbing. Specifically on the back of the inner fender. I JUST clear mine with turning (and that was with some modification to the inner fender) so you will rub for sure. You will definitely be trimming the plastic and possibly bending the metal behind it a little bit as well.

If you want to stay as flush as possible you need a 20x9 0 offset. With that you'll be sticking out around 1 5/8" on the front and 1 1/8" on the back. So still poking a bit to get a nice stance.

Thanks I appreciate the info greatly... Wasn't 100% on the offset direction, I was reading your other thread and saw where you had to trim. I will pm you got more info.

Thanks

fastNugly @ BP 06-06-2013 01:31 AM

These guys know their stuff and are always first to respond. Love it :smileup:

1LOWBLKRAM 06-07-2013 02:59 PM

Decided on the Fuel Throttles after seeing both wheels in person. Went with a 20x10 -12 offset 35x12.5x20 Nitto Trail Grapplers, Readylift kit 2.5 upfront 1.5 rear and will be adding a 1.25 body lift next month to gain a little more clearance. Should have it all on and Ready to go tomorrow afternoon.

1LOWBLKRAM 06-07-2013 03:01 PM

Also got a crazy deal on a set of OEM painted Fenderflares for $150 couldn't pass up that offer... Looking forward to seeing the completed product.

Grubrunner 06-07-2013 03:04 PM

Quote:

Originally Posted by 1LOWBLKRAM (Post 1119215)
... Looking forward to seeing the completed product.

So are we.... ....


All times are GMT -4. The time now is 03:52 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vB.Sponsors
= Copyright RamForumZ.com a Gigathreads.com Network Site =Ad Management by RedTyger