DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum

DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum (http://www.ramforumz.com/index.php)
-   Suspension (http://www.ramforumz.com/forumdisplay.php?f=168)
-   -   84 W250 front hub/rotor? (http://www.ramforumz.com/showthread.php?t=155245)

bkyzn5 10-09-2013 01:47 AM

84 W250 front hub/rotor?
 
Does'nt the hub come off of the rotor, and HOW? Please and thank you

RogerRamJet 10-09-2013 02:24 AM

Do you mean rotor come off the hub? The answer would be no. Bearings are in the rotor, they are one piece. You have to pull the dust cover off, remove the cotter pin and then the hub nut, then the rotor will slide off the hub with the bearing attached.

bkyzn5 10-09-2013 02:52 PM

Yes yes thats what i mean. Trying to replace the rotor but its not possible at the moment unless these are two separate parts. What dust cover are you referring to? :4-dontknow:

bkyzn5 10-09-2013 02:55 PM

Trying to attach a pic but the m***&^*#! wont upload for some reason. It seems the studs are pressed into the rotor from the backside and the hub is just setting in it, over the studs. It looks like the two should be pried apart but nothing will budge.

Warlock III 10-09-2013 03:07 PM

http://www.partsgeek.com/assets/dimage/full/1139023.jpg

Did you try wacking it between the studs with a BFH?

Just for future reference...It's a lot easier to pull the rotor off the hub while it's still on the truck.

http://thumbs3.ebaystatic.com/d/l225...d7Sxz5QG0A.jpg

RRJ! tell 'em how to post a picture! :LOL:

There's a few good tutorials in the "Suggestions-Feedback-Tech Support"...(then click) "How To's" up top, or follow this link: http://ramforumz.com/forumdisplay.php?f=73

RogerRamJet 10-10-2013 01:49 AM

Quote:

Originally Posted by Warlock III (Post 1217945)

RRJ! tell 'em how to post a picture! :LOL:

I remember something about putting your left foot in and shaking it all about.:doh:

bkyzn5 10-13-2013 01:25 AM

Yes yes it was just a BFH that needed and it did the trick, knocked the studs through and it came right off. Thanks!! Picked up a 20 gal parts washer today to lower the intensity on this little job a ton.
Hey now I figured out HOW to upload a pic, but was encountering some kind of error. Comments like that typical of a Texan.. :hah:

RogerRamJet 10-13-2013 01:50 AM

Quote:

Originally Posted by bkyzn5 (Post 1220168)
Yes yes it was just a BFH that needed and it did the trick, knocked the studs through and it came right off. Thanks!! Picked up a 20 gal parts washer today to lower the intensity on this little job a ton.
Hey now I figured out HOW to upload a pic, but was encountering some kind of error. Comments like that typical of a Texan.. :hah:

Hey! I resemble that remark!


All times are GMT -4. The time now is 11:39 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
vB.Sponsors
= Copyright RamForumZ.com a Gigathreads.com Network Site =Ad Management by RedTyger