DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum

DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum (http://www.ramforumz.com/index.php)
-   Exhaust (http://www.ramforumz.com/forumdisplay.php?f=142)
-   -   Installing headers? (http://www.ramforumz.com/showthread.php?t=87261)

kwatson 07-16-2011 04:31 PM

Installing headers?
 
Abyone here install shorty headers on a 4.7 Ram? I have an '06 4X4 and want to install headers. I see Gibson sells some for $350 that are direct replacement for the manifolds. Is it easy? Or are there some obsticles? I've installed headers on older vehicles, but never a computer controlled vehicle. I guess I'm just saying, never on my daily driver that cost $17k! :SHOCKED: Only on $2-3k cars, so I'm a bit nervous about it. Next I want to change the cams to the 212, and finally, 4.56 gears (35" tires)

marshallsmith44 07-16-2011 07:41 PM

Im working on getting the same mods you want to get i will probably do headers soon I know it isn't a huge job but can be allitle tricky

Stormtroop 4.7 07-20-2011 05:40 PM

I've heard some bad reviews about the Gibsons and that they were prone to cracking. There are some JBA headers on Airram for 360 though if you decide to go with a different brand. With the mods you have planned it sounds like your truck will be pretty sweet.

snrusnak 07-21-2011 01:17 PM

I think OBX (ebay brand) sells some too they may be cheaper. I've heard nothing but good things about the OBX company (on other vehicles).

marshallsmith44 07-21-2011 02:25 PM

same here snrusnak, ive looked at them but i havent found any that fit 06-07 but i could be over looking them

snrusnak 07-21-2011 02:30 PM

Yeah I'm not sure, I don't even know what's available for my 2010, just know I saw OBX makes some for some 4.7L rams.... I plane to get shorties eventually also.

There's a set of JBA stainless on ebay

http://cgi.ebay.com/ebaymotors/JBA-1...#ht_1644wt_782

This is the first time I've ever heard someone complain about gibson products...

CamoBoy34 01-22-2012 03:31 PM

i just installed a set of JBA stainless steel shortys on my 05 and they fit real good in the chassis and every where else. the only problem i had was that the passenger side header sat back about 3 inches to far. i just cut the exhaust after the cat and am gonna run it like that till i get to an exhaust shop to have the cats cut out and have it done right ;) other then that i like the look and sound especially coming straight out the headers

snrusnak 01-22-2012 11:17 PM

^cool keep us updated on performance improvements!

I wish someone would make headers for the new 4.7L...

CamoBoy34 01-24-2012 01:33 PM

the improvements with the headers were amazing. i went from a 14 second 0-60 to a 10 second 0-60. and the throttle response is better also

snrusnak 01-24-2012 01:37 PM

14 second 0-60!?!? My stock truck with tune runs 15's in the 1/4 mile....

Something must have been wrong with your engine.


All times are GMT -4. The time now is 05:36 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vB.Sponsors
= Copyright RamForumZ.com a Gigathreads.com Network Site =Ad Management by RedTyger