DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum

DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum (http://www.ramforumz.com/index.php)
-   Dodge Ram Knowledge Base (http://www.ramforumz.com/forumdisplay.php?f=41)
-   -   HOW TO: Disabling Seatbelt Chime (VIDEO) (http://www.ramforumz.com/showthread.php?t=87388)

HoosierHemi 07-18-2011 09:56 AM

HOW TO: Disabling Seatbelt Chime (VIDEO)
 
http://www.youtube.com/watch?v=nyzBvCQKucw&hd=1

1- lock seatbelt in
2- turn ignition to "ON"
3- wait for seatbelt warning light to remove from dash
4- remove and insert seat belt 3 times within 10 seconds
5- leave seatbelt in on the 3rd time
6- turn ignition to "OFF"
7- listen for chime to confirm operation worked

EDIT: Still not working, sorry, I'll update this if a solution is found....

Jonesey982 07-18-2011 10:54 AM

Thanks for the info. I'm going to try this on my 3rd gen and see if it works.

Quickdrop 07-24-2011 05:51 PM

ty for this dude

BgHrn 07-24-2011 07:21 PM

Would this work on a 06' Ram 1500?

tastoffel 08-23-2011 04:04 AM

This is what I found on another forum (http://www.**************/forums/sho...ight=horn+honk). (I guess this will not show)
I haven't had time to test it yet, but my guess is that it should work.

The Enhanced Warning System (BeltAlert) can be enabled
or disabled by your authorized dealer or by
following these steps:
NOTE: The following steps must occur within the first
60 seconds of the ignition switch being turned to the ON
or START position. The manufacturer does not recommend
deactivating the Enhanced Warning System
(BeltAlert).
1. With all doors closed and the ignition switch in any
position except On or Start, buckle the driver’s seat belt.
2. Turn the ignition switch to the ON position and wait
for the Seat Belt Warning Light to turn off.
3. Within 60 seconds of turning the ignition switch to the
ON position, unbuckle and then re-buckle the driver’s
seat belt at least three times within 10 seconds, ending
with the seat belt buckled.
4. Turn the ignition switch to the LOCK position. A
single chime will sound to signify that you have successfully
completed the programming.
The Enhanced Warning System (BeltAlert) can be reactivated
by repeating this procedure.
NOTE: Although the Enhanced Warning System
(BeltAlert) has been deactivated, the Seat Belt Warning
Light will continue to illuminate while the driver’s seat
belt remains unbuckled.


I'm still looking to disable the horn when locking the truck and get a blink on the lights instead. Up to now I only found a way to disable both, the locking and unlocking signals.

Reducing the horn sound to a small chirp would be ok too, but not the original sound.

2006ramhemi 09-05-2011 09:16 PM

i just tried this on my 2006 ram and it worked on the first try. drove around with it unbuckled and there was no chime. i wear my seatbelt anyway but i unbuckle when im parking or pulling up to an atm so its nice not to hear anything. when it comes on i get scared it might be the check engine light or something

BlackHemI 09-15-2011 12:34 PM

freaking sweet! i have an 08 1500 and did it before work today, and BAM no annoying chime! thanks bro reps coming your way!

Green 1500 11-03-2011 03:43 PM

I have a 2011 1500, and it worked. Did it yesterday.

GeauxHunting 11-03-2011 04:16 PM

I did this on my 05, but I buckled and unbuckled 5 times, but not as quick as you did it and it worked.

HeyBrownDog 11-08-2011 07:01 PM

Worked Perfect.....thanks!!!!!


All times are GMT -4. The time now is 06:21 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vB.Sponsors
= Copyright RamForumZ.com a Gigathreads.com Network Site =Ad Management by RedTyger