DODGE RAM FORUM - Ram Forums & Owners Club! - Ram Truck Forum - Search Results
DODGE RAM FORUM - Ram Forums & Owners Club! - Ram Truck Forum

Go Back   DODGE RAM FORUM - Ram Forums & Owners Club! - Ram Truck Forum > Search Forums


Notices


Vendor Highlight! - Check these guys out for great deals on Parts and Accessories!
Showing results 1 to 13 of 13
Search took 0.00 seconds.
Search: Posts Made By: andrew93
Forum: 5.7L V8 Specific Topics 08-03-2013, 06:28 PM
Replies: 2
Views: 386
Posted By andrew93
Differential help

I have a 03 ram 1500 with a hemi and ive had a humming noise coming from the passenger side rear so i pulled the diff cover of to change the fluied and found metal laying in it and it looks like a M...
Forum: 4.7L PowerTech V8 Specific Topics 08-02-2013, 05:33 PM
Replies: 10
Views: 2,252
Posted By andrew93
is the passenger floor board wet? could be the...

is the passenger floor board wet? could be the heater core
Forum: 4.7L PowerTech V8 Specific Topics 07-31-2013, 11:38 PM
Replies: 16
Views: 887
Posted By andrew93
Here's a picture of the number 1 cylinder wall...

Here's a picture of the number 1 cylinder wall let me know what y'all think going to take it to the machine shop tomorrow and see what he says also if I run my finder nail over the scratches I can...
Forum: 4.7L PowerTech V8 Specific Topics 07-31-2013, 11:29 PM
Replies: 16
Views: 887
Posted By andrew93
ok was looking at the cylinder walls again and #1...

ok was looking at the cylinder walls again and #1 has scratches on the wall up and down so guess thats were im losing the compression and i am going to do a complete rebuild
Forum: 4.7L PowerTech V8 Specific Topics 07-31-2013, 08:46 PM
Replies: 16
Views: 887
Posted By andrew93
Ok i have the motor completely apart and all the...

Ok i have the motor completely apart and all the valves are seating properly the 2 or 3 of the rod bearings make noise when i move them side to side not a lot of play just a little in them so going...
Forum: 4.7L PowerTech V8 Specific Topics 07-30-2013, 06:11 PM
Replies: 16
Views: 887
Posted By andrew93
The heads were redone by a good machine shop and...

The heads were redone by a good machine shop and he replaced the valves I also noticed that a few of exhaust valve don't seat all the way when the cam and rocker arms are installed and I have a...
Forum: 4.7L PowerTech V8 Specific Topics 07-29-2013, 10:29 PM
Replies: 16
Views: 887
Posted By andrew93
i have the valve covers off now all of the push...

i have the valve covers off now all of the push rods are were there suppose to be. also when i had the head off the block wouldnt i have seen problems if there was a dead cylinder when i had the...
Forum: 4.7L PowerTech V8 Specific Topics 07-29-2013, 08:30 PM
Replies: 16
Views: 887
Posted By andrew93
ok rented a compression tester from autozone im...

ok rented a compression tester from autozone im getting around 60 and 80 psi and on the cylinder on the driver side first one from the front is reading 0 when i had the heads off getting done at the...
Forum: 4.7L PowerTech V8 Specific Topics 07-29-2013, 04:01 PM
Replies: 16
Views: 887
Posted By andrew93
Anyone else have any Ideas?

Anyone else have any Ideas?
Forum: 4.7L PowerTech V8 Specific Topics 07-28-2013, 02:59 AM
Replies: 16
Views: 887
Posted By andrew93
ive checked the vacuum lines i can see and all...

ive checked the vacuum lines i can see and all good but could be missing one ive had a few of these 4.7's and one i had to do timing on and it was a tooth off had a slight miss. So i triple checked...
Forum: 4.7L PowerTech V8 Specific Topics 07-28-2013, 02:50 AM
Replies: 16
Views: 887
Posted By andrew93
02 4.7 rought idles dies

I just bought a 02 ram with a 4.7 had a blown head gasket and 3 valve seats dropped valve barley touched the top of the pistons also cylinder walls looked very good not scratches or marks. Took the...
Forum: 4.7L PowerTech V8 Specific Topics 12-09-2012, 02:46 PM
Replies: 3
Views: 508
Posted By andrew93
Anyone Have any ideas?

Anyone Have any ideas?
Forum: 4.7L PowerTech V8 Specific Topics 12-08-2012, 11:07 PM
Replies: 3
Views: 508
Posted By andrew93
2002 4.7 timing

I have a 02 ram 4.7 had to change the oil pump so got it all back together and it runs but at idle has a little shake kinda like a miss and when taking off from a stop doesnt have the best get up and...
Showing results 1 to 13 of 13

 
Forum Jump


Advertisement



All times are GMT -4. The time now is 12:11 PM.


vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright © VerticalScope Inc. All rights reserved.
Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
vB.Sponsors