DODGE RAM FORUM - Ram Forums & Owners Club! - Ram Truck Forum

Go Back   DODGE RAM FORUM - Ram Forums & Owners Club! - Ram Truck Forum > Search Forums


Notices


Vendor Highlight! - Check these guys out for great deals on Parts and Accessories!
Total Load Control!
AutoAnything
Addictive Desert Designs!
FGT Motorsport
Bayou Goat Mounts
Mopar Online Parts!

Showing results 1 to 13 of 13
Search took 0.00 seconds.
Search: Posts Made By: tav
Forum: Heating & Cooling 12-05-2016, 12:36 PM
Replies: 2
Views: 76
Posted By tav
blowing thru rad. cap

hi guy maybe you can help or insite. (2003 dodge hemi 5.7 4x4) so 3 months ago we changed the heater core .....very leaky. plus before the change a garage replaced the water pump and thermostat...
Forum: 5.7L V8 Specific Topics 10-16-2016, 05:09 AM
Replies: 0
Views: 53
Posted By tav
2003 ram 1500 hemi ign. coil

got an 2003 hemi and the plugs have been changed a few times including the other day along with ing. coils.


question: whats the average life span on these coils, my truck had 194,000...
Forum: Heating & Cooling 09-16-2016, 11:19 AM
Replies: 3
Views: 118
Posted By tav
garage changed water pump and thermostat, as i...

garage changed water pump and thermostat, as i drive home yesterday a 1/4 from home i hear a small rumble as i gave it gas and the temp went up. so today i did the by pass and seemed to go well. ...
Forum: Heating & Cooling 09-15-2016, 07:06 PM
Replies: 3
Views: 118
Posted By tav
by pass heater core (help please)

2003 1500 ram. i need to by pass the H/core. where can i get a pre form U shape hose. and what sizes would be looking for ? i also need the insert connectors.
Forum: 5.7L V8 Specific Topics 09-10-2015, 11:34 PM
Replies: 0
Views: 59
Posted By tav
Cv boot half shaft

2003 ram 4x4.
Got a rip in my cv boot so I guess I need to swap out the shaft .
I know I got to break the hub nut....can I break it with a breaker bar?
Forum: Suspension 01-02-2015, 09:29 AM
Replies: 1
Views: 1,107
Posted By tav
upper and lower ball joints

hi there.... I have a 2003 1500 ram 4x4 with 165.000 on it and just bought some
mevotech lowers and upper control arm joint.

cost was an issue so I had to cheap out , has any one used this...
Forum: 5.7L V8 Specific Topics 08-07-2014, 09:30 AM
Replies: 0
Views: 195
Posted By tav
steering noise

ok so up to now every time I turned the steering wheel (sitting still) I heard this clunking noise while turning, I thought I had a ball joint problem. took the tire and looked at possible ball...
Forum: Exhaust 07-24-2014, 10:25 AM
Replies: 0
Views: 308
Posted By tav
muffler parts

trying to replace a 2003 1500 dodge muffler (140" w/b) with a walker . the hangers on the muffler look a little short but seem in the right area. what are those rubber parts that attach to the...
Forum: 5.7L V8 Specific Topics 07-16-2014, 01:07 PM
Replies: 2
Views: 492
Posted By tav
a little help with exhaust please

2003 1500 4x4 crew cab....muffler went on this truck so ended up getting a walker...# 50317 off set...off set. pretty sure my muffler is the same when I looked. will this muffler fit really close...
Forum: Electrical 09-09-2013, 11:42 AM
Replies: 2
Views: 418
Posted By tav
update...... went to a rv shop and they spliced...

update...... went to a rv shop and they spliced in a converter to the blinker....now it works... :)
Forum: Electrical 09-09-2013, 07:59 AM
Replies: 2
Views: 418
Posted By tav
need an expert opinion

2003 ram 1500


well I think I know the answer but here it goes, maybe there's another solution?

all lights and blinkers WORK on the truck.... but when I hook up the to trailer all lights...
Forum: Electrical 09-01-2013, 03:43 PM
Replies: 1
Views: 314
Posted By tav
trailer blinker problem

hi all....first post on this site.

I have a 1500 ram in which I pull a 16' boat . yesterday the left rear blinker wasn't working, I couldn't change bulbs cuz the light assy is sealed(water...
Forum: Newbie Checkin! 09-01-2013, 03:31 PM
Replies: 7
Views: 283
Posted By tav
hi there

checking in from ct.
Showing results 1 to 13 of 13

 
Forum Jump


Advertisement







All times are GMT -4. The time now is 06:29 AM.


= Copyright RamForumZ.com a Gigathreads.com Network Site =Ad Management by RedTyger
Powered by vBulletin® Version 3.8.10 Release Candidate 2
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
vB.Sponsors