DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum

Go Back   DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum > Search Forums


Notices


Latest Vendor News
AutoAnything
Addictive Desert Designs!
Bayou Goat Mounts

Showing results 1 to 25 of 28
Search took 0.02 seconds.
Search: Posts Made By: Cammin Hemi
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 01-23-2012, 02:54 PM
Replies: 13
Views: 4,073
Posted By Cammin Hemi
Thanks Chef!! I'll check my fuel trims and...

Thanks Chef!! I'll check my fuel trims and proceed with the torque converter.
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 01-22-2012, 08:37 PM
Replies: 13
Views: 4,073
Posted By Cammin Hemi
How much higher will the rpm's be during normal...

How much higher will the rpm's be during normal city driving after installation? Maybe 2 to 300? Or maybe still close to stock ( keeping my heavy foot under control:smileup: )? I'm hoping the...
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 01-20-2012, 04:51 PM
Replies: 13
Views: 4,073
Posted By Cammin Hemi
Thanks for quick responses!:wavey: I feel alittle...

Thanks for quick responses!:wavey: I feel alittle easier now about making this mod.:smileup: Around town and on the highway will the rpms be higher? If so, I'm not concerned about it because I have...
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 01-20-2012, 10:36 AM
Replies: 13
Views: 4,073
Posted By Cammin Hemi
545rfe torque converter

Anybody running an Edge torque converter? I'm looking at a 2800 stall. What differences did you notice both on the street and the strip? I've never made changes to an automatic trans before....
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 01-30-2011, 10:52 AM
Replies: 6
Views: 1,579
Posted By Cammin Hemi
Thanks guys! I have found a set of pipes on line,...

Thanks guys! I have found a set of pipes on line, but there is no picture ( JBA mid pipes ). I'M trying to find stainless to go from my headers to the muffler without cats. Most everything is three...
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 01-28-2011, 03:00 PM
Replies: 6
Views: 1,579
Posted By Cammin Hemi
Y Pipe?

:4-dontknow:Has anyone ever found a y pipe without catalytic converters for the Hemi? I haven't had any luck searching. My Edelbrock shortys use a factory 2 bolt connection at the collectors....
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 01-25-2011, 04:43 PM
Replies: 11
Views: 1,084
Posted By Cammin Hemi
I've been running a 180 t-stat for a year with no...

I've been running a 180 t-stat for a year with no problems.
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 12-29-2010, 11:19 PM
Replies: 1
Views: 357
Posted By Cammin Hemi
Wide band o2

I'm almost ready to install my air/fuel gauge and wide band o2 sensor. The gauge is going to be installed in a A pillar pod. I picked the driver side bank for the wide band oxygen sensor. Anybody...
Forum: Exhaust 12-16-2010, 11:41 AM
Replies: 5
Views: 611
Posted By Cammin Hemi
:smileup:Thanks Chef! I was thinking about 2.5 to...

:smileup:Thanks Chef! I was thinking about 2.5 to the mufflers ( true duals no cats with x-pipe before mufflers ) and 3 inch tail pipes. The rear 02's are programmed out. What do you...
Forum: Exhaust 12-08-2010, 04:48 PM
Replies: 5
Views: 611
Posted By Cammin Hemi
:smileup:Thanks Daytona! I was guessing either...

:smileup:Thanks Daytona! I was guessing either 2.0 or 2.25. I know between the converter and muffler it's an odd 2.75 size.
Forum: Exhaust 12-08-2010, 01:22 PM
Replies: 5
Views: 611
Posted By Cammin Hemi
Question Exaust Pipe Diameter

:wavey:Hello everyone out there in Ram land! Does anyone know the diameter of the exaust pipe between the catalytic converter and the exaust manifold?
Thanks!!!!
Forum: 5.7L V8 Specific Topics 11-16-2010, 04:54 PM
Replies: 12
Views: 796
Posted By Cammin Hemi
It could be your spin on filter under the trans...

It could be your spin on filter under the trans pan is leaking. I would try changing this filter & the main sump filter and see what happens.
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 11-05-2010, 09:46 AM
Replies: 17
Views: 3,650
Posted By Cammin Hemi
Code p2138 is for throttle pedal position. The...

Code p2138 is for throttle pedal position. The flash at a dealer will relearn your new throttle body as far as pedal position at wot, idle and everything in between.
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 11-04-2010, 09:45 AM
Replies: 17
Views: 3,650
Posted By Cammin Hemi
What p-codes are you getting now? Are you running...

What p-codes are you getting now? Are you running a stock tune? When it's running does it run smooth? Is the idle speed the same? A vacumme leak could be the problem.
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 10-29-2010, 10:28 AM
Replies: 2
Views: 647
Posted By Cammin Hemi
Did you have to pull the whole trans or just drop...

Did you have to pull the whole trans or just drop the pan & valve body?
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 10-28-2010, 10:47 AM
Replies: 2
Views: 647
Posted By Cammin Hemi
Transgo Reprogramming Kit

Has anyone tired this Transgo 545RFE reprogramming kit? Any good? Thanks______________!!!!!!!!!
Forum: 5.7L V8 Specific Topics 10-25-2010, 09:35 AM
Replies: 4
Views: 945
Posted By Cammin Hemi
Could be a rear u-joint. Try a slow roll in...

Could be a rear u-joint. Try a slow roll in reverse with your head out the driver door. Any driveline vibration on acceleration?
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 10-18-2010, 11:56 AM
Replies: 2
Views: 278
Posted By Cammin Hemi
Air fuel guage

I'm thinking about installing an air/fuel guage. I currently still have the factory cats on both banks. Could I put the wideband 02 sensor just before the muffler where the 2 pipes y into one? Or to...
Forum: 5.7L V8 Specific Topics 10-18-2010, 08:51 AM
Replies: 10
Views: 3,522
Posted By Cammin Hemi
There are three possibilites. On a cold start-up...

There are three possibilites. On a cold start-up you will get alittle steam & water as the engine heats up the condensation in the exaust. This should quit after afew minutes. A leaking head gasket...
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 10-17-2010, 07:32 PM
Replies: 16
Views: 1,172
Posted By Cammin Hemi
Here's a recent video one of my friends took. ...

Here's a recent video one of my friends took.

http://www.youtube.com/watch?v=FQ3XPz6FF_A&feature=player_profilepage
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 10-16-2010, 08:53 PM
Replies: 16
Views: 1,172
Posted By Cammin Hemi
Kay9, What cam are you running? Sean is a great...

Kay9,
What cam are you running? Sean is a great MOPAR tuner! I might be stuck with the surge using this 273H. I quess I should have done more research, but in the summer of 2008 I couldn't find many...
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 10-16-2010, 09:15 AM
Replies: 16
Views: 1,172
Posted By Cammin Hemi
I've been running this set-up for about 2 years...

I've been running this set-up for about 2 years now. The tuning was a real headache. Hemifever got it running the best it ever has. Others had tried and my hat is off to him!!! It does not pull hard...
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 10-15-2010, 01:31 PM
Replies: 16
Views: 1,172
Posted By Cammin Hemi
Comp 273H

Anybody running this cam? My engine will surge about 100 rpm or better with foot off accelerator around 30/35 mph. Would a 2800/3000 stall converter help smooth this out? Other than that it runs...
Forum: Custom Dodge Ram Performance Mods - Engine - 5.7 HEMI V8 09-24-2010, 09:51 AM
Replies: 18
Views: 1,617
Posted By Cammin Hemi
Before I would get to deep in the cam selection I...

Before I would get to deep in the cam selection I would find a good Chrysler/Dodge engine tuner. It's not going to be very driveable, if at all depending on how radical the cam is, untill the engine...
Forum: 5.7L V8 Specific Topics 09-23-2010, 11:52 AM
Replies: 17
Views: 4,788
Posted By Cammin Hemi
A Dodge master tech once told me when the heads...

A Dodge master tech once told me when the heads were machined the holes for the pushrods were drilled just a slight smidge to large causing the infamous Hemi tick. It should never cause any...
Showing results 1 to 25 of 28

 
Forum Jump


Advertisement






All times are GMT -4. The time now is 05:48 AM.


= Copyright RamForumZ.com a Gigathreads.com Network Site =Ad Management by RedTyger
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vB.Sponsors


=Gigathreads Network=
CLUBS MOPAR NATION DSM GPMM MAMM JAM
DIESEL Diesel Forum      
CHEVY Chevy Camaro Forum Chevy Volt Forum    
CHRYSLER Chrysler 300C Forum      
DODGE Dodge Avenger Forum Dodge Caliber Forum Dodge Challenger Forum Dodge Charger Forum
  Dodge Circuit Forum Dodge Hornet Forum Dodge Magnum Forum Dodge Nitro Forum
  Dodge Ram Forum Dodge Dakota Forum Dodge Durango Forum Dodge Dart Forum
FORD Ford Raptor Forum Ford F150 Forum Ford F100 Forum  
JEEP Jeep Forum      
PONTIAC Pontiac G8 Forum      
SRT SRT Viper Forum SRT Cuda Forum