View Single Post
  #18  
Old 06-20-2013, 09:07 PM
RedSmart's Avatar
RedSmart RedSmart is offline
Dodge Ram Forum Senior Member!
 
Join Date: May 2013
Location: Toronto
Age: 48
Posts: 1,056
Gender: Male
Vehicle: 2013 Ram 1500 Hemi 8-speed
Trim Level: Big Horn
Color: Black
Engine: 2009-20?? 345ci (5.7L) Hemi V8 390hp 407lb/ft
Rep Power: 3
Rep:883
RedSmart is a splendid one to beholdRedSmart is a splendid one to beholdRedSmart is a splendid one to beholdRedSmart is a splendid one to beholdRedSmart is a splendid one to beholdRedSmart is a splendid one to beholdRedSmart is a splendid one to behold
Default

Quote:
Originally Posted by moose3 View Post
Well everyone here is my review of the Bakflip F1 for Rambox.

It took about a week for my Bakflip to arrive. It was packed very well, everything was nice and tidy in the package. I watched a video of the install on Youtube and the instructions feature color photos, so the installation process is not to hard to get figured out. The kit installs with just basic hand tools.

I bought this cover because I needed something that was easy to remove/fold up on a fairly regular basis, and I haul motorcycles so I couldnít have the wasted 6 inches at the top side of the bed, that is where front wheel of a bike hits. I also wanted a cover that I could sit something on. Now that the cover is installed it looks great, the rubber flaps that go all the way around the edge lay and down and seal very nicely, they have a decent amount of pressure on them to keep them sealed up. The cover folds up easily and can be put in the locked upright position with ease. The cover doesnít lock up right completely rigid, so I think on big bumps it will bang around. It is also marketed as been non-heat gathering, but today it was 90 degrees and sunny and it got hot enough that would barely want to touch it for more than a moment. This may be cooler than the all aluminum ones, but not without heat. One more thing is that you have to open the cover before you can close the tailgate.

I did run into some issues with the install. The drain cups for the rear of the mounting rails was not cut to accommodate a clip that holds the bed cap corner down. So I had to cut that to make it fit (see photo). The right angle aluminum that works as the catch for the latches is slotted to allow you get it to the proper height, but the captured nut embeds itself in the back of the brackets, which makes them rather difficult to adjust. Once I had them all adjusted and installed I installed the panel system. But when I flip the panels down to the latches are wider than the catches, so they will not close. The latches were 1/8Ē too wide. I emailed Bak and then called them. The customer service rep told me that they would have a senior tech call me back. Well I never heard from them.

I could have waited days for them to call, we shall see if they ever call back. I could have demanded a return, but I want the cover and I had already waited a week to get it. So I decided to remedy the situation myself. I removed the catch brackets and marked them off and took them to my industrial belt sander. I removed a 1/8 from each bracket, so I would have clearance to latch the cover. I then put a nice radius on the corners something that Bak didnít do. I repainted them and reinstalled again dealing with the difficult to adjust part. The cover still would not latch now because the latches on the cover are plastic and the edge of the catches would dig in. I then had to take a sanding flap wheel and radius the edge to get a nice smooth edge. The cover now fits and latches just like it does in the promo video they so proudly show us.

Now for the disappointment part in the system in general, the bracketry that comes with it, while fully functional is kind of crude. The catches are a piece of cut down angle aluminum, with slots in them. The corners just knocked off, rather than taking the extra 5 seconds to radius the corners on the same sander they are using to knock the corners down. (see photo) The retainer for the prop rod has to be the most disappointing piece, it is a Ĺ inch chunk of angle aluminum that is hand drilled and sanded, then has a plastic wire retainer riveted to it. (see photo) This is the kind of the thing you go hey that will work, when you are engineering in your garage, not what you expect on a cover that is $900-$1000! Yes it does the job. For a company that is touting that they build OEM parts for one of the BIG 3, I am not sure how this level of quality can pass.
I like the cover, it works, it was just a long journey to get it on and right. I donít have any intentions of replacing it, and yes I may even consider it for another truck. I was suggesting a Rollbak for my dads truck (different set of needs), but I may now look into a similar design by a different manufacture.
Take this information and make your own purchasing decision.
Hi Moose3 thanks for the review.

I have a question for you that I wondered if you could help me out with?

I too have Ramboxes and have the F1 halfway installed, but I came across a situation on the mounting rod assembly similar to what you were talking about.

Could I trouble you to take a picture of the two pieces that make up the positioning of the mounting rod and post it?

I would be talking about the pieces in steps 7 and 8 of the installation.

I'm pretty sure that Bak sent me the wrong parts (though I'm sure I could make it work), but I'd be curious as to how your setup looks.

Here is the piece that they sent me that I think is wrong, but workable.

Thanks.
Attached Images
File Type: jpg BakFlip F1b.jpg (98.3 KB, 24 views)
Reply With Quote