DODGE RAM FORUM - Ram Forums & Owners Club! - Ram Truck Forum - View Single Post - Blacking Out your stock 20's: Basic How Too!
View Single Post
Old 09-07-2010, 12:31 AM
RamTex's Avatar
RamTex RamTex is offline
Dodge Ram Forum Senior Member
Join Date: Apr 2010
Location: Mineola, Tx
Age: 31
Posts: 1,537
Gender: Male
Vehicle: 2009 Dodge Ram 6.6L Hemi!
Trim Level: Crew Cab Sport 4x4
Color: Stone White
Rep Power: 8
RamTex is just really niceRamTex is just really niceRamTex is just really niceRamTex is just really nice
Default Blacking Out your stock 20's: Basic How Too!

I did this mod about 2 1/2 months ago and had a few people wanting a how too. So here you go.

Ok so basically your going to need to decide how you want to paint these. Whether or not you want to just paint the outer most part of the rim or the whole thing, in which case i would remove the tires. I just painted the outer most part. No removal of the tires needed.

Supplies....This is what you need minimum! 1 or 2 cans extra wont hurt. I mean you dont want to need one and not have it. So if you can paint like a pro then the amount listed should be enough.

1. 2 foam 120 grit sanding pads.
2. 1 bucket of water/water hose
3. 3 cans of Duplicolour Primer
4. 4-5 cans Duplicolour Chrysler Brilliant Black
5. 4-5 cans Duplicolour Clear Coat
6. 1 roll of 3M masking tape like 2 inch's wide .
7. Plastic Trash Bags (To tape off the rims)
8. Jack/Jack stands, ( I used four stands)
9. Tools to remove the lugs.

Step 1. Of coarse remove the wheels. Clean the rims as good as you can to remove all the oil, grit, and grime.

Step 2. Sand till you cant really see your reflection, should be like a brushed aluminum look. Use lots of water here, the key is to keep the foam pad wet.

Step 3. Clean again to remove any oil and shavings from the sand that got back on the wheel. Then just let them dry.

Step 4. Once dry you can start taping off the rim, you want to get tape between the rim of the wheel and the tire. Then slip your gigantic trash bag over the wheel. And cut out enough to let you re-tape to the tape that you put down previously.

Step 5. Double check the tape for gaps, once you feel comfortable start your primer coat. I only did one. NO Sanding is need and if you are that picky then dang.

Step 6. Let the coat dry for like 35 - 40 minutes minimum, that's pretty standard. Then go ahead and shoot the first Black Paint coat. Let it dry then paint the next. Let it dry then paint then next. Let it dry.

Step 7. Clear coat time! Same... Paint, Let it dry, Paint, Let it dry, Paint, Let it dry. Once it's dry pull the garbage bag off and re-use it on the rest. Then remove the original tape around the rim to finish it off.

Step 8. Almost done! At this point you got to give the clear coat time to settle. This could take around 3-4 hrs respectively you will see the change in texture don't worry just give it time. Once you feel comfortable put the suckers back on and your good to go. to see the pics!
This is pretty much exactly what i did to my rims so there yah go my first Z how too!

"New Project" 1969 Road Runner
BV Heads,K1 Crank and Rods,Corrillo Pistons,ARP Head, Main, Side Studs and Rod Bolts,Spartan Eagle Cam,6.1 Manifold,Fastman 85mm,LMI Hammer, ARH's,3000TC,Hemifever Tuning

Last edited by RamTex; 09-07-2010 at 02:12 AM.
Reply With Quote