View Single Post
  #23  
Old 10-13-2010, 10:59 PM
moparornocar72's Avatar
moparornocar72 moparornocar72 is offline
Dodge Ram Forum Member


 
Join Date: Aug 2010
Location: Auburn, AL
Age: 25
Posts: 3,661
Gender: Male
Vehicle: 2010 Dodge Ram
Trim Level: Big Horn
Color: Mineral Grey
Engine: 2009-20?? 345ci (5.7L) Hemi V8 390hp 407lb/ft
Rep Power: 6
Rep:630
moparornocar72 is a name known to allmoparornocar72 is a name known to allmoparornocar72 is a name known to allmoparornocar72 is a name known to allmoparornocar72 is a name known to allmoparornocar72 is a name known to all
Default

Sorry I am just now getting in from work and school:
Engine Controls ECM Update For Spark Knock/Vibration
NUMBER: 18-041-08
GROUP: Vehicle Performance
DATE: December 16, 2008
THE StarSCAN(R) FLASH FILES FOR THIS BULLETIN MUST BE RETRIEVED FROM THE INTERNET.
StarSCAN(R) SOFTWARE LEVEL MUST BE AT RELEASE 9.03 OR HIGHER FOR THIS BULLETIN.
StarMOBILE STANDALONE MODE OR StarMOBILE DESKTOP CLIENT MAY ALSO BE USED TO PERFORM THIS PROCEDURE.
SUBJECT:
FLASH: Spark Knock Improvements And Noise Vibration Harshness (NVH) Improvements

OVERVIEW:
This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM).

MODELS:
2009 DS Ram Truck 15002009 (WK) Grand Cherokee2009 (WH) Grand Cherokee (International Markets)2009 (XK) Commander2009 (XH) Commander (International Markets)
NOTE :This bulletin applies to vehicles built with a 5.7L engine (sales code EZD) on WK/WH/XK/XH built before October 28, 2008 (1028XX MDH) or DS vehicles built before October 3, 2008 (1003XX MDH).

SYMPTOM/CONDITION:
Some customers may experience:
^NVH issues while the vehicle is operating in the MDS mode.
^Spark Knock between 1800 to 2500 RPM.

DIAGNOSIS:
Using a Scan Tool (StarSCAN(R)) with the appropriate Diagnostic Procedures available in TechCONNECT, verify all engine systems are functioning as designed. If DTC's are present other then the one listed above record them on the repair order and repair as necessary before proceeding further with this bulletin.
If no DTC's are present, perform the Repair Procedure.

PARTS REQUIRED:

SPECIAL TOOLS / EQUIPMENT REQUIRED:
REPAIR PROCEDURE:
1.Reprogram the PCM with the latest software. Follow the detailed service procedures available in DealerCONNECT/TECHCONNECT, Refer To 8 - Electrical/Electronic Control Modules/Powertrain Control Module - Standard Procedure PCM/ECM Programming - Gas.
2.Type the necessary information on the "Authorized Modification Label" p/n 04275086AB and attach it near the VECI label.
POLICY:
Reimbursable within the provisions of the warranty.


TIME ALLOWANCE:

FAILURE CODE:
Disclaimer :This bulletin is supplied as technical information only and is not an authorization for repair.

Engine Controls Poor Idle Quality
NUMBER: 18-038-08
GROUP: Vehicle Performance
DATE: October22, 2008
THE StarSCAN(R) FLASH FILES FOR THIS BULLETIN MUST BE RETRIEVED FROM THE INTERNET.
StarSCAN(R) SOFTWARE LEVEL MUST BE AT RELEASE 9.03 OR HIGHER FOR THIS BULLETIN.
StarMOBILE STANDALONE MODE OR StarMOBILE DESKTOP CLIENT MAY ALSO BE USED TO PERFORM THIS PROCEDURE.
SUBJECT:
Flash: Idle Quality Improvements
OVERVIEW:
This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software.
MODELS:
2009 (DS) Ram 1500 Truck
NOTE : This bulletin applies to two wheel drive (4x2) models equipped with a 5.7L engine (sales code EZD) built before October 3, 2008 (MDH 1003XX).
SYMPTOM/CONDITION:
Some customers may complain of the idle quaility after the vehicle is warmed up. This condition can happen while the vehicle is in park, neutral, drive or reverse with no additional throttle tip in. A software change has been made to the increase the warm nominal idle speed from 584 rpm to 648 rpm, which corrects the condition.
If the vehicle owner complains of this issue reprogram the PCM with the new software.
DIAGNOSIS:
Using a Scan Tool (StarSCAN(R)) with the appropriate Diagnostic Procedures available in TechCONNECT, verify all engine systems are functioning as designed. If DTC's are present record them on the repair order and repair as necessary before proceeding further with this bulletin.

PARTS REQUIRED:

SPECIAL TOOLS / EQUIPMENT REQUIRED:
REPAIR PROCEDURE - USING THE INTERNET TO RETRIEVE THE FLASH FILE:
1.Reprogram the PCM with the latest software. Follow the detailed service procedures available in DeaIerCONNECT/TECHCONNECT, Refer To 8 - Electrical/Electronic Control Modules/Powertrain Control Module - Standard Procedure PCM/ECM Programming - Gas.
2.Type the necessary information on the "Authorized Modification Label" p/n 04275086AB and attach it near the VECI label.
POLICY:
Reimbursable within the provisions of the warranty.

TIME ALLOWANCE:

FAILURE CODE:
Disclaimer :This bulletin is supplied as technical information only and is not an authorization for repair.

HOPE THIS IS WHAT YOU WANTED, LET ME KNOW IF THERE IS ANYTHING ELSE I CAN DO!
__________________
14.268 @ 95 MPH Full Trim

Proudly Sponsored by Bully's Performance
Reply With Quote