DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum

Go Back   DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum > Dodge Ram Forum - Help Zone - Dodge Ram Problems, Complaints, & Solutions - Maintenance & Re > 3RD Generation Dodge Ram 2002 to 2008 Dodge Ram Trucks > Electrical


Notices

Electrical 3rd Gen Dodge Ram Electrical Problems and Questions.


Latest Vendor News
AutoAnything
Addictive Desert Designs!
Bayou Goat Mounts

Reply
 
Thread Tools
  #1  
Old 06-17-2013, 03:36 PM
thekid0311 thekid0311 is offline
Dodge Ram Forum Member

 
Join Date: Apr 2013
Location: Marion NC
Age: 25
Posts: 74
Gender: Male
Vehicle: 2005 Doge Ram Quad cab 4x4
Trim Level: Daytona
Color: Silver
Engine: 2003-2008 345ci (5.7L) Hemi V8 345hp 375lb/ft
Rep Power: 0
Rep:15
thekid0311 is on a distinguished road
Default Transmission temp gauge help.

Ok I put a T fixture on my outlet line of my tranny. I used 3/8ths compression fittings to clamps down the ends of where I cut into the line and then I have a 3/8th to 1/8th reducer on the end that sticks up for my sender. Its been JB welded so I have a warm and fuzzy that it wont leak. Ive got it all wired up and ive got power and Im getting a temp reading of 68 on gauge but it doesn't move from there. I have the sender grounded to the O2 sensor of the cat. Is that causing interference and not reading a temp or is it just a bad sender? Thanks in advance for the help.
__________________
Men will follow out of fear but will die over respect
Reply With Quote
Sponsored links
  #2  
Old 07-14-2013, 09:04 AM
hriczko806's Avatar
hriczko806 hriczko806 is offline
Dodge Ram Forum Senior Member!
 
Join Date: May 2012
Location: Lehigh Valley, PA.
Posts: 194
Gender: Male
Vehicle: 2004 Ram Quad Cab
Trim Level: SLT
Color: Black
Engine: 2003-2008 345ci (5.7L) Hemi V8 345hp 375lb/ft
Rep Power: 3
Rep:91
hriczko806 will become famous soon enough
Default

Dont know if your still having this issue... I just installed a trans temp gauge as well as the manifold.

First which line do you have the manifold tapped into? Is it the line going to or from the trans cooler? Also you said you have the sender facing up?

The manifold should be on the line from the transmission to the cooler. Also The sender needs to be pointed down so that the fluid can pool inside and it can get a proper reading. Do you have a digital gauge or analog? If it has a needle check the fitment of the gauge in the gauge pod. I saw on youtube a guy installed his and commented that he had his gauge installed too tightly and it was actually coming in contact with the needle so it couldnt move past a certain point. One last thing... I dont think it matters but I would try to ground it to something else. When I installed mine the sender had one wire that went directly to the gauge so I didnt have to ground anything on the manifold. Only what was required by the gauge.

Hopefully this helps you out a bit.
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Advertisement






All times are GMT -4. The time now is 07:54 AM.


= Copyright RamForumZ.com a Gigathreads.com Network Site =Ad Management by RedTyger
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vB.Sponsors


=Gigathreads Network=
CLUBS MOPAR NATION DSM GPMM MAMM JAM
DIESEL Diesel Forum      
CHEVY Chevy Camaro Forum Chevy Volt Forum    
CHRYSLER Chrysler 300C Forum      
DODGE Dodge Avenger Forum Dodge Caliber Forum Dodge Challenger Forum Dodge Charger Forum
  Dodge Circuit Forum Dodge Hornet Forum Dodge Magnum Forum Dodge Nitro Forum
  Dodge Ram Forum Dodge Dakota Forum Dodge Durango Forum Dodge Dart Forum
FORD Ford Raptor Forum Ford F150 Forum Ford F100 Forum  
JEEP Jeep Forum      
PONTIAC Pontiac G8 Forum      
SRT SRT Viper Forum SRT Cuda Forum