DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum

Go Back   DODGE RAM FORUM - Ram Forums and Owners Club! - Dodge Truck Forum > Dodge Ram Forum - Help Zone - Dodge Ram Problems, Complaints, & Solutions - Maintenance & Re > 3RD Generation Dodge Ram 2002 to 2008 Dodge Ram Trucks > Powertrain > 4.7L PowerTech V8 Specific Topics


Notices


Latest Vendor News
AutoAnything
Addictive Desert Designs!
United Radio
Bayou Goat Mounts

Reply
 
Thread Tools
  #1  
Old 01-24-2011, 11:52 PM
uptheirons uptheirons is offline
Dodge Ram Forum Newcomer
 
Join Date: Sep 2010
Location: Calgary, Alberta
Age: 29
Posts: 7
Gender: Male
Vehicle: 2003 Dodge Ram
Trim Level: SLT
Color: Tan
Engine: 2002-2007 287ci (4.7L) PowerTech V8 235hp 295lb/ft
Rep Power: 0
Rep:10
uptheirons is on a distinguished road
Default P0132

had this code for a little while, tried replacing both 02 sensors, came back both times... i'm sure this has been posted in the forum before but i couldn't find it. My Haynes manual says "Upstream oxygen sensor (left cylinder bank), circuit voltage too high.

Any insight from anyone? anyone had this problem before?

Thanks in advance!
Reply With Quote
Sponsored links
  #2  
Old 01-25-2011, 01:04 AM
Pecos Bill Pecos Bill is offline
Dodge Ram Forum Junior Member
 
Join Date: Sep 2009
Age: 65
Posts: 42
Gender: Male
Engine: 2003-2008 345ci (5.7L) Hemi V8 345hp 375lb/ft
Rep Power: 0
Rep:10
Pecos Bill is on a distinguished road
Default

What does that mean?

This involves the front oxygen sensor on Bank 1. This code indicates that the heated oxygen sensor reading is too high. That indicates the voltage at the sensor is over 1.5 volts. You will likely not notice any drivability problems.
Causes

A code P0132 may mean that one or more of the following has happened:
  • <LI itxtvisited="1">The oxygen sensor heater circuit is shorted out
  • The wiring to the sensor is broken / frayed (less likely)
Possible Solutions

The simplest thing to do is to reset the code and see if it comes back.
If the code comes back, the problem is more than likely the front Bank 1 oxygen sensor. You will likely wind up replacing it but you should also consider these possible solutions:
  • <LI itxtvisited="1">Check for wiring problems (shorted, frayed wires)
  • Check the voltage of the oxygen sensor
http://www.obd-codes.com/p0132
Reply With Quote
  #3  
Old 01-25-2011, 01:09 AM
uptheirons uptheirons is offline
Dodge Ram Forum Newcomer
 
Join Date: Sep 2010
Location: Calgary, Alberta
Age: 29
Posts: 7
Gender: Male
Vehicle: 2003 Dodge Ram
Trim Level: SLT
Color: Tan
Engine: 2002-2007 287ci (4.7L) PowerTech V8 235hp 295lb/ft
Rep Power: 0
Rep:10
uptheirons is on a distinguished road
Default

I'll give it a try! thanks.
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Advertisement






All times are GMT -4. The time now is 10:30 PM.


= Copyright RamForumZ.com a Gigathreads.com Network Site =Ad Management by RedTyger
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
vB.Sponsors


=Gigathreads Network=
CLUBS MOPAR NATION DSM GPMM MAMM JAM
DIESEL Diesel Forum      
CHEVY Chevy Camaro Forum Chevy Volt Forum    
CHRYSLER Chrysler 300C Forum      
DODGE Dodge Avenger Forum Dodge Caliber Forum Dodge Challenger Forum Dodge Charger Forum
  Dodge Circuit Forum Dodge Hornet Forum Dodge Magnum Forum Dodge Nitro Forum
  Dodge Ram Forum Dodge Dakota Forum Dodge Durango Forum Dodge Dart Forum
FORD Ford Raptor Forum Ford F150 Forum Ford F100 Forum  
JEEP Jeep Forum      
PONTIAC Pontiac G8 Forum      
SRT SRT Viper Forum SRT Cuda Forum